Hyd Xpthc-300-PT Arc Voltage Plasma Torch Height Controller

• Customization: Available
• Cooling Method: Water Cooling
• Frequency Band: High Frequency
• Model NO.: XPTHC-300-PT
• Cutting Material: Copper, Carbon Steel, Iron, Aluminum, Metal Alloy, Stainless Steel
• Automatic Grade: Automatic
• Power Source: Electric
• Cutting Mode: Plasma Cutting
• Input Power: DC24V+10%
• up/Down Motor: DC24V DC Motor
• Motor Drive: PWM
• Output Current: 1A-4A
• Max Capacity: 100W
• Working Temperature: -10~60c
• Ihs: Proximity Switch Ihs & Retaining Cap Ihs
• Voltage Divide Ratio: 50:1
• Transport Package: Carton
• Specification: 272 x 225 x 80mm
• Trademark: HYD
• Origin: China
• Production Capacity: 50000PCS/Year

Product Description

Product Description

 XPTHC-300-PT
supports almost all plasma cutters on market like Hypertherm, Thermal Dynamics...
supports all CNC cutting controllers on market like Hypertherm

XPTHC-300-PT can start Auto Height control with or without Auto enable signal from CNC.
But with Auto enable/disable signal from CNC, THC would work better.all plasma cutters on market like Hypertherm, Thermal Dynamics...

supports all CNC cutting controllers on market like Hypertherm,

Safety and installation precautions:
- Before using this product, be sure to read the instruction manual of this height controller carefully to avoid installation or operation errors and cause unnecessary losses.
- Special Note: The power supply voltage of this height controller is AC24V/DC24V power supply.
- Non-professionals or unauthorized persons cannot open the height controller for inspection and maintenance;
- Do not arbitrarily open the adjustable resistor sealed with screw glue to adjust it;
- When not in use, please turn off the power of this height controller in time.
- Do not put liquid on the height controller, so as not to enter the height controller.
- Pay attention to dust prevention, do not let metal dust, etc. enter the height controller.
- When handling, please handle with care to avoid damage.
- The grounding position of the height controller must be well grounded, and the grounding resistance is less than or equal to 1ohm.
- According to the positioning method used, set the correct positioning method of the height controller.
- The ascending and descending directions on the height controller panel must be consistent with the lifter.
- The arc voltage of the plasma must be connected to the voltage divider plate or the voltage divider positioning plate, and the plasma anode cable must be connected to the workpiece.
- The initial positioning operation of the protective cap contact type can be carried out only on the upper side.
- Please do not install the height controller in the place of heat source, the normal working temperature of the height controller is -10ºC~60ºC. Take appropriate protective measures in environments with high temperature, humidity, dust or corrosive gases.

Package Included:
- 1 x XPTHC-300-PT without Protective Cap Positioning
- 1 x Voltage Divider
- 2 x Filter Rings
- 1 x Proximity Switch (diameter 12mm; NPN normally open close to 2mm)

 

 

Product Parameters

Input power	DC24V+10% &  AC24V+10%, 50Hz/60Hz
Up/Down motor	DC24V DC MOTOR
Motor Drive	PWM
Output Current	1A-4A
Max capacity	100W
Working temperature	-10∽60°C
IHS	Proximity switch IHS & Retaining cap IHS
Run transmission mode	Output the successful signal when the arc voltage is detected.
Voltage Divide ratio	50:1
Control accuracy	±1V∽±2V (related to lifter and motor voltage )
Size(length *width *height )	272mmX225mmX80mm
The speed of lifting	800mm/min∽4000mm/min(recommend 2500mm/min)
Setting Arc Voltage arrange	30V∽250V, According to different applications
Overload Protection Mode	PWM mode with overload protection.
Test Max cutting speed	24000mm/min (Related to customer's lifter voltage ,speed and sensitive setting. )

 

Company Profile